How to setup FSK telemetry reception with RTL-SDR Blog V4 and SDR#?

 Setting up an RTL-SDR Blog V4 with SDR# (SDRSharp) for FSK telemetry reception requires installing the V4-specific rtlsdr.dll library, routing un-filtered discriminator audio through a virtual audio cable, and configuring SDR#’s demodulator so digital bit transitions pass without distortion.

1. Install RTL-SDR Blog V4 Drivers for SDR#

Because the RTL-SDR Blog V4 uses an R828D tuner with a built-in HF upconverter and notch filters, standard legacy Osmocom drivers will not tune it properly.

  1. Extract SDR#: Download the standard 32-bit sdrsharp-x86.zip package from Airspy and extract it to a writable folder (such as C:\SDRSharp), avoiding C:\Program Files where Windows restricts write permissions.
  2. Fetch the V4 DLL: Double-click install-rtlsdr.bat inside the extracted folder. Current releases of this script automatically pull the RTL-SDR Blog V4 branch of rtlsdr.dll. (If using an older SDR# installation, download the latest Release.zip from the rtlsdrblog/rtl-sdr-blog GitHub repository and copy the x86 versions of rtlsdr.dll, msvcr100.dll, and pthreadVC2.dll into your SDR# folder, overwriting existing files.)
  3. Install WinUSB via Zadig: Plug in the V4 dongle, right-click zadig.exe in the SDR# folder, and select Run as administrator. Click Options → List All Devices, select Bulk-In, Interface (Interface 0), ensure the target driver is set to WinUSB, and click Install/Replace Driver.
  4. Source & Bias-Tee Configuration: Open SDRSharp.exe, set Source to RTL-SDR USB, and click the Configure (gear) icon. Set the sample rate to 2.4 MSPS (or 1.024 MSPS for lower CPU load). If you are powering a masthead LNA on VHF/UHF, check Offset Tuning—on the RTL-SDR Blog V4, this toggle activates the 4.5 V bias tee.

2. Configure Virtual Audio Routing

SDR# demodulates the RF carrier into baseband audio, which must be passed cleanly to your FSK decoding software without acoustic microphone distortion.

  1. Install VB-Cable (or Virtual Audio Cable) and open Windows Sound Settings.
  2. Under both Playback (CABLE Input) and Recording (CABLE Output), open Properties → Advanced and set the format to 16-bit, 48000 Hz (DVD Quality) with all audio enhancements disabled.
  3. In SDR#’s Audio panel, set Output to [MME] CABLE Input (VB-Audio Virtual Cable).

3. Critical SDR# Demodulator Settings for FSK

Standard voice-oriented settings in SDR# will strip out low-frequency components and corrupt FSK bitstreams. Apply these exact parameters in the

Radio and

Audio panels:

  • Modulation Mode: Select NFM (Narrow FM) for direct FM-FSK and GFSK telemetry beacons (such as 200 bps UNNE-1B or 800 bps HADES-L downlinks). (Select USB only if your decoder expects an SSB-demodulated audio-tone FSK stream.)
  • Uncheck “Filter Audio” (Essential): In the Audio panel, uncheck Filter Audio. When checked, SDR# applies a ~300 Hz high-pass filter and FM de-emphasis curve that rounds off flat-topped digital pulses and causes high bit-error rates. Unchecking it outputs raw discriminator audio.
  • Bandwidth: Set between 12,000 Hz and 15,000 Hz to encompass the carrier shift and baud rate (BW ≈ 2Δf + Rb) without admitting excess adjacent noise.
  • Squelch: Leave unchecked (OFF) so weak telemetry frames are not clipped at the start of a packet burst.
  • Manual RF Gain: In the Configure (gear) window, uncheck RTL AGC and Tuner AGC, then raise the RF Gain slider manually—typically to 32–42 dB on VHF/UHF—until the noise floor rises cleanly by 8–12 dB without overloading from nearby transmitters.
  • AF Gain (Volume Slider): Set the top volume slider in SDR# to roughly 50%–65% so the signal reaches your decoder at mid-scale without clipping.

4. Doppler Tracking & Decoding

  • Automated Doppler Correction: For Low Earth Orbit satellites on 70 cm (~436 MHz), Doppler shift spans roughly ± 10 kHz across an overhead pass—wide enough to push an FSK signal outside a 12 kHz NFM filter. Link Gpredict to SDR# via the DDE Tracker plugin (or use SatPC32) so the receiver VFO tracks the pass automatically.
  • Live or Offline Decoding: Launch your telemetry decoder—such as UZ7HO SoundModem (including builds tailored for HADES-L/UNNE-1B), Dire Wolf, or gr-satellites—and select CABLE Output as its input device. For post-pass analysis, enable SDR#’s Audio Recorder (with Filter Audio unchecked) to capture a clean discriminator .WAV file for offline decoding tools like AMSAT-EA’s HADESx Generic Decoder.